2023 Land Rover Range Rover Evoque Transmission Owners Manual

2023-Land-Rover-DEFENDER-LOGO

2023 Land Rover Range Rover Evoque Transmission

2023-Land-Rover-Range-Rover-Evoque-Product-Image

AUTOMATIC TRANSMISSION

2023 Land Rover Range Rover Evoque Transmission-Fig-01
WARNING

Before exiting the vehicle, make sure that the vehicle is stationary. Select Park (P). Make sure the Electric Parking Brake (EPB) is applied. Switch the engine off. The vehicle can move unexpectedly with any other gear position selected, which may result in death or serious injury.

WARNING

Do not allow the vehicle to remain stationary with a drive gear selected and the engine running. If the engine is to idle for a prolonged period, select P or Neutral (N) and apply the EPB. The vehicle may move unexpectedly with any other gear position selected, which may result in serious injury or death.

CAUTION

Never select P while the vehicle is in motion. Doing so can result in serious transmission damage.

CAUTION

Never select Reverse (R) while the vehicle is in forward motion. Doing so can result in serious transmission damage.

CAUTION

Never select a forward gear while the vehicle is moving backwards. Doing so can result in serious transmission damage.

The gear selection status of the gear selector and the steering wheel’s paddle shift is displayed in the instrument panel. The appropriate indicator light on top of the gear selector, illuminates to confirm selection.

NOTES

When the gear selector is released, after normal operation, it returns to the central position, except for when in the Sport (S) position.

NOTES

If the driver’s door is opened and the brake pedal is released, while the vehicle is stationary, then P will be automatically selected. Once P has been automatically selected, if RN, Drive (D) or Sport (S) is reselected, P is not automatically selected again unless the driver’s door is closed and reopened.

  1. Press to select P. The P indicator lamp illuminates to confirm.

    Select P before switching off the ignition.

    NOTES

    P can be selected from any gear selector position.

    NOTES

    P cannot be selected by manually moving the gear selector.

    NOTES

    If the ignition is switched off with N selected, the system waits for 10 minutes before automatically selecting P. With the EPB released, this procedure allows for the vehicle to be conveyed through a car wash and should not be used for vehicle recovery purposes.

  2. When the vehicle is stationary, press the brake pedal before selecting DN, or R.
  3. With the brake pedal still pressed, press the button to allow the gear selector to be moved:

    Rearward to select D.

    Forward a short way to select N.

    Forward a long way to select R.

    NOTES

    The button must be pressed in order to make most gear selections. A button press is not required when selecting N from D or R. A button press is also not required when moving between S and D.

  4. While in D, move the gear selector one side movement to select S.
    NOTES

    Reverse this action to return to D.

  5. While in S, manual selection of the gears can be made by pulling the gear selector back for up-shifts and pushing forward for down-shifts.

    Manual gear selection status is displayed in the instrument panel.

    The relevant gear selector indicator shows the status of the manual gear selection:

    Continuous illumination confirms the driver’s gear change request is recognized and selected.

    On or off flashing confirms the driver’s gear change request is recognized but not selected.

  6. Gearshift paddles: Allow for manual gear selection while in or S. Lightly pull the left paddle for down-shifts, or lightly pull the right paddle for up-shifts. To exit manual mode, pull and hold the right paddle for approximately 1 second. The gear will return directly to the previous automatic operation in D or S.
GEARSHIFT PADDLE:

Sequential shift can be effective when rapid acceleration and engine braking are required. A gear shift indicator warning light illuminates briefly at the recommended gear change point. See GEARSHIFT (GREEN). If the gear selector remains in the D position, temporary use of the manual gear selection mode is held while the driver is accelerating. The manual gear selection is also held while decelerating, cornering or continuing to request gearshift changes via the steering wheel gearshift paddles.

NOTES

If continued use of the gearshift paddles is required, select S.

The driver can configure the gearshift paddles to be active in both D and S, or active in S only, via the touchscreen:

  1. Touch the settings icon¹ from any screen.
  2. Touch the ALL soft key.
  3. Touch the Vehicle soft key.
  4. Touch the Convenience soft key.
  5. Touch the Gear shift paddles soft key.
  6. Touch the forward arrow in the box below Gear shift paddles active in to open the options menu.
  7. Choose Sport only or Drive and Sport.
  8. Touch the exit icon² to return to the previously displayed screen.
2023 Land Rover Range Rover Evoque Transmission-Fig-02

Settings icon.¹

2023 Land Rover Range Rover Evoque Transmission-Fig-03

Exit icon.²

LIMP-HOME MODE

If a transmission system fault is detected, the instrument panel displays the warning message Gearbox Fault. If possible, the vehicle should be carefully driven to the nearest place of safety. In this event, seek qualified assistance.

WARNING

The driver should be aware that the vehicle’s performance is reduced. Failure to take this into account when driving may result in accidents causing serious injury or death.

NOTES

The use of the steering wheel’s paddle shifts is disabled.

Some transmission faults may cause gear selector softlock. In this event, the gear selector can be moved, but it does not allow a gear request to be made until the ignition is switched off and on again. Either a flashing or permanent Neutral (N) gear status in the instrument panel indicates that the driver’s gear request cannot be engaged. In the event of a permanent N, directly select the required gear. In the event of flashing gear, select N first, and then select the required gear again.

If the transmission is still unable to engage the requested gear, contact a retailer/authorized repairer.

Leave a Comment